全自动超声波清洗注意保持机械清洁干净：专用超声波清洗机一般安装在某些特定物件清洗的生产流水线上，被清洗物件从进料口可传动到不锈钢专用网带送人超声波清洗槽清洗，在经喷淋、烘干等工序后出料，实现被清洗物件可直接包装入库。

Pay attention to keeping the machinery clean in automatic ultrasonic cleaning: the special ultrasonic cleaning machine is generally installed on the production line for cleaning some specific objects. The cleaned objects can be transmitted from the feeding port to the stainless steel special mesh belt and sent to the ultrasonic cleaning tank for cleaning. After spraying, drying and other processes, the materials are discharged, so that the cleaned objects can be directly packed and stored in the warehouse.

一台清洗机用多个换能器，经粘接剂粘接在清洗刚底部且经并联连接组成一台清洗机的换能器，换能器基元之间距对频率20kH4一般在5—10mm为佳，太大了容易产生弯曲振动，且振动板受到腐蚀，同时辐射面相对减少。

A cleaning machine uses multiple transducers, which are bonded to the bottom of the cleaning steel by adhesive and connected in parallel to form the transducer of a cleaning machine. The distance between the transducer elements and the frequency of 20kh4 is generally 5-10mm. If it is too large, it is easy to produce bending vibration, and the vibrating plate is corroded, and the radiation surface is relatively reduced.

严禁从超声波控制柜顶端的进风口处溅入导电液体(如水)。否则会对清洗机的线路系统造成严重损害。超声波清洗机注意保持机器清洁，不使用时关掉电源。避免对机器的碰撞或剧烈震动。远离热源。机器应避免在潮湿的环境下存放。

Do not splash conductive liquid (such as water) from the air inlet at the top of the ultrasonic control cabinet. Otherwise, it will cause serious damage to the circuit system of the cleaning machine. Pay attention to keep the ultrasonic cleaning machine clean and turn off the power when not in use. Avoid collision or violent vibration to the machine. Keep away from heat sources. The machine should not be stored in a humid environment.

机器连续工作时间不得超过4小时，如连续工作时间过长：应旋转超声调节旋钮“0”位，而让散热风扇继续工作，在超声波清洗不启动的状态下为超声波控制柜内持续散热少2分钟。

The continuous working time of the machine shall not exceed 4 hours. If the continuous working time is too long: rotate the ultrasonic adjusting knob to the "0" position, and let the cooling fan continue to work. When the ultrasonic cleaning is not started, the heat dissipation in the ultrasonic control cabinet shall be continued for at least 2 minutes.

经长时间运行的清洗机，在停机前应将功率旋钮调零位，使用其风机再工作3-6分钟后关机，以保证电源内部热量散出。清洗液应及时沉淀、过滤或更换，以保证清洗效果。

For the cleaning machine that has been operated for a long time, the power knob should be adjusted to zero before shutdown, and the fan should be used to work for another 3-6 minutes before shutdown, so as to ensure the internal heat dissipation of the power supply. The cleaning solution should be precipitated, filtered or replaced in time to ensure the cleaning effect.

超声波发生器产生高频高压，通过电缆联结线传导给换能器，换能器与振动板一起产生高频共振，超波清洗机主要由超声波清洗槽和超声波发生器两部分构成。超声波清洗槽用，底部安装有超声波换能器振子，坚固弹性好、耐腐蚀的不锈钢制成；从而使清洗槽中的溶剂受超声波作用对污垢进行洗净。

The ultrasonic generator generates high-frequency and high-voltage, which is transmitted to the transducer through the cable connecting line. The transducer and the vibrating plate produce high-frequency resonance together. The ultrasonic cleaning machine is mainly composed of two parts: ultrasonic cleaning tank and ultrasonic generator. For ultrasonic cleaning tank, the bottom is equipped with ultrasonic transducer vibrator, which is made of solid, elastic and corrosion-resistant high-quality stainless steel; Thus, the solvent in the cleaning tank is cleaned by ultrasonic wave.

请勿用手去调节功率旋钮，应确保功率旋钮在小处，打开电源后，以免清洗液浸入电位器内部，超声波清洗机大功率模块启动频繁，对设备使用寿命有所影响。

Do not adjust the power knob by hand. Make sure the power knob is in a small place. After turning on the power supply, it will prevent the cleaning fluid from immersing in the potentiometer. The high-power module of the ultrasonic cleaner starts frequently, which will affect the service life of the equipment.

全自动超声波清洗机的清洗池中的水位低于侧面振板(清洗池长度方向侧板的凸出部分)时，应先将功率旋钮旋到小处工作23分钟，造成该机无法正常工作或损坏设备。如运行中突然停电，请迅速关掉电源开关并将功率旋钮旋小处，以免重复停送电，严禁开机，否则会对清洗机造成严重伤害。

When the water level in the cleaning pool of the full-automatic ultrasonic cleaning machine is lower than the side vibration plate (the protruding part of the side plate in the length direction of the cleaning pool), the power knob should be turned to a small position to work for 2 to 3 minutes, causing the machine to fail to work normally or damage the equipment. In case of sudden power failure during operation, please turn off the power switch quickly and turn the power knob to a small position to avoid repeated power cut and transmission. It is strictly forbidden to start the machine, otherwise it will cause serious injury to the washing machine.

打开电源开关前，将功率旋钮逐渐旋到大处。关闭电源时，然后再关闭电源。当被清洗工件浸没于清洗溶液中时，超声波以强大的空化效果作用于工件的内外表面，故其特别适合于复杂多孔、不能有硬物擦洗的光洁表面。

Before turning on the power switch, turn the power knob gradually to a large position. Turn off the power before turning it off. When the cleaned workpiece is immersed in the cleaning solution, the ultrasonic wave acts on the inner and outer surfaces of the workpiece with a strong cavitation effect, so it is especially suitable for the smooth surface with complex pores and no hard objects to scrub.

以上就是今天为大家介绍的关于问题以及注意事项的全部内容，希望对大家能有所帮助，想要了解更多内容可以电话联系我们或者关注我们的网站，我们的工作人员会及时与您取得联系。

The above is all about the problems and precautions introduced to you today. I hope it can help you. If you want to know more, you can contact us by phone or follow our website www.jnthcsb COM, our staff will contact you in time.